DIY house from an old bus. How to make a motorhome on wheels yourself: photos of finished work

At the moment, there are several classifications of mobile homes. Based on the main design features, the following categories can be distinguished:

trailed;
camper van;
a caravan house connected to transport.

Mobile modern houses can be divided into types not only according to certain design features, but also according to their purpose. This category includes mobile homes that are used as permanent or long-term housing, as well as those that are intended exclusively for travel.

You can find more detailed information about what it is in a very useful and interesting article by our specialist.

There is another form of classification of modern motorhomes. They can be divided into three main categories:

C – small-sized, used for short trips;
C B – semi-integrated car houses;
B A – fully integrated.

The first ones are made on the basis of a regular SUV; the sleeping places here need to be transformed in a special way. Class B motorhomes are distinguished by a permanently located sleeping place, which is located in the rear of the vehicle. Class A motorhomes are similar in appearance to regular buses. They are quite comfortable and, therefore, very expensive in cost if purchased ready-made.

To save money, you can build a mobile home with your own hands, using photos and special instructions as a guide. If you correctly carry out the main stages of manufacturing a motor home, you can get a vehicle that will have a large windshield, a fixed driver's seat, as well as special retractable partitions that form zones of different functionality and separately located sleeping places.

Below you will find information on how to make a mobile home with your own hands, which can be considered autonomous. The structures can be equipped with generators, have gas supplied and a sufficiently large supply of water.

Stages of building a motorhome with your own hands

If you want to build a motorhome with your own hands, you should carefully follow the instructions provided. Below we describe how to build a motorhome body depending on the base, how to properly equip it and equip it with all the necessary components for living and traveling.

Creating a plan

Homemade mobile homes are quite serious structures. The process of their construction, here, as in any important event, must begin with a detailed plan. It is at this stage of work that the master must think through the most basic aspects of the matter, all possible little details and draw up the most accurate drawing.

When making a motorhome from a trailer with your own hands, you need to strictly adhere to all the points and rules indicated in the plan and drawings.

The total internal space of a building on wheels should be divided into three main zones:

A dining room where you can eat, work on a laptop or read a newspaper at the table. Here you can place a small sofa, chairs and a table. These items should fold easily enough to take up a minimum amount of free space.
Sleeping area. This is one of the important areas, since adequate sleep ensures activity and good mood. For a driver, night rest is very important, since his concentration and attentiveness depend on it, which directly affects the safety of movement during the daytime. It is advisable to equip this area with a comfortable bed, which should easily rise and free up space.
Bathroom with toilet. To equip such an area, you need to install a sink, a shower stall and a modern dry closet.
Kitchen. This zone takes up a minimum amount of space, since most of its elements are built-in. To ensure maximum comfort, you need to install two burners, a small sink, a countertop, a small refrigerator and an extractor hood.

Due to the fact that the standard room of a motorhome is quite limited, its zones need to be integrated into one another. It is for this reason that a preliminary plan is so important and must be followed carefully.

In the process of drawing up a plan, you need to carefully consider what interior items are really required and what you can refuse.

After this, everything desired, indicating the exact dimensions, is transferred to a sheet of paper. Next, the plan is drawn up according to the following principle:

The estimated area of the motorhome is divided into pre-divided zones. For example, a bedroom needs more space than a kitchen;
the location of the bathroom and options for separating it from other rooms are noted;
All furniture elements are drawn, as well as methods of their fastening and folding options.

In the process of drawing and designating these areas of the room, it is necessary to take into account the dimensions of each element.

Don't forget about free space too. The mobile home should not be littered with things and pieces of furniture.

After drawing up a detailed and well-thought-out plan, after specifying the dimensions of the common room and pieces of furniture, you can begin to build such a structure as a mobile home from a trailer with your own hands.

Selecting a base

Among the most affordable budget options that are optimal for everyone who likes to make something with their own hands, we can highlight three of the most convenient designs. You can make a residential trailer with your own hands on the basis of a gazelle, a trailer with a reinforced chassis and an old minibus. Let's look at two of them in more detail.

Minibus

To make a motorhome with your own hands from a minibus, you should begin by thoroughly cleaning the body and removing the upholstery. After this, you need to make special holes for ventilation, under the windows and for gas supply. After these general preparatory works, you can begin special processes related to the arrangement of the residential area. Work of this kind must be performed in the following sequence:

Leveling any dents on the inner surface and priming all metal parts of the base. This will prevent the occurrence of destructive corrosion.
The internal surface - walls, ceiling and floor - are covered with heat-insulating material.
A moisture-resistant coating is laid on top.
Gas and electricity are provided.
Bathroom equipment is being manufactured.
The kitchen is being equipped and furniture is being installed.

It is equally important to get your travel van's engine and chassis in order. Due to the fact that this is a mobile vehicle, its ability to move should be given no less close attention than its arrangement and comfort.

Trailer

Making a camper from a trailer with your own hands is much more difficult than making a camper from a minibus. The main difficulty is that the walls and ceiling need to be built from scratch. An approximate scheme of action in this case will be as follows:

Cleaning the chassis and trailer.
Mounting on the base of the frame of the future motorhome.
Covering the frame with a layer of plywood.
Floor installation with simultaneous use of thermal insulation.
The structure is sheathed with external material and coated with special moisture-resistant compounds.
Roof arrangement.
Construction of a drain, installation of wires to provide the house with electricity.
Installation of door and window openings.

All this is a general scheme for making a house on wheels. Below each stage will be discussed in more detail.

Exterior finishing work

Once the main body of the mobile home is ready, the main exterior work can begin. It is very important to ensure that the campsite is kept as clean as possible. There should be no dust, dirt or significant defects. This is what guarantees the successful formation of the structure. The main points of external work include:

Removal of corrosion and various types of damage.
Making holes.

Speaking about the necessary openings, it can be noted that these are not only window openings, but also those designed for gas outlet, ventilation, and water filler necks.

Openings must be made during the process of arranging the camper. Otherwise, you may encounter certain difficulties.

The external arrangement of such a structure as a do-it-yourself mobile home from a minibus or trailer consists of performing the following work:

Creating partitions between the main body and the front seats.
Arrangement of internal insulation. Here you need to remember that the overall temperature and sound insulation inside the room will directly depend on the quality and proper installation of this material.
Covering the structure from the roof to the floor covering.

There are a huge number of different materials available on the modern market. The choice can be made based on personal preferences, environmental characteristics, general financial situation, and the type of body used.

Home equipment

The equipment of a motorhome lies largely in its internal arrangement. To make the house convenient and comfortable, you will need to install water, electricity, gas into the house, and also install certain furniture.

Water supply and bathroom

A prerequisite for water supply to a structure on wheels is to ensure the supply of running water. To carry out this process, you need to install a couple of canisters and a compact pump under the sink, which will provide the necessary flow of water to the tap.

Thinking through the drainage of wastewater is the basic rule when arranging a full-fledged toilet. They can be removed using a special hose located in the floor surface. With a little engineering knowledge, you won't have to manually drain water into special portable tanks. Although many people do this too.

As for the bathroom, the best option is to purchase and install a dry closet.

Electricity

One or more special batteries may be entirely responsible for the accumulation and storage of electricity in a wheeled house. These devices can be charged while the tractor is operating or when connected to external sources. When equipping a motorhome with electrical networks, modern inverters occupy a special place. These are special devices that are capable of converting direct current with a voltage of 12 V into alternating current equal to 230 V. Due to this, devices operating from a 230-volt standard can be connected to a 12-volt network without any problems.

Heating and gas

Gasification of the described design consists of simply installing a gas cylinder in the room. To do this, you need to select a separate closed area. In its lower part you need to arrange special holes that go out.

Tom Grantham, 29, and Kylie Barnes, 30, spent $2,000 to buy back an old shuttle bus - and turned it into a luxury caravan for a family of five with all the amenities and even a fireplace!
How did they do it? Let's get a look!

When Tom Grantham and Kylie Barnes bought a 23-year-old shuttle bus for $2,000 in 2011, probably no one but them believed that any good would come of this purchase. The couple had to invest many months of work and about $15,000 to turn it into a super home on wheels, equipped with everything a family with three children would need for a vacation.

The husband has personal memories associated with this bus: as it turned out upon purchase, it ran on route 51 from Grimsby to Louth for many years, passing the couple’s house every day. Now it has become their very own luxury travel van.

Tom and Kylie have three children - three-year-old Henry, seven-year-old Poppy-Mae and eight-year-old Logan. They won't be cramped in the former bus converted by Tom!

The main living room of the caravan has two wide sofas. You can sit on them with the whole family, admiring the views, and if necessary, they can be converted into two wide double beds. “This is the perfect car for a family weekend trip!” - says Tom. He was mainly involved in the technical part and furniture manufacturing, and Kylie became the interior designer.

Tom built all the necessary amenities in the mobile home, providing it with a stove, oven, gas fireplace, sink, toilet and shower. All that remains from the previous bus is the traditionally designed driver's seat.

To fit a bedroom for three children in the car, we had to try hard, using all the vertical space, from floor to ceiling.

The kitchen-living room in the central part of the van is decorated with light wood and has maximum light.

The family travels in their caravan to music festivals across Britain, as well as holidays to France and Belgium.

However, when trying to go to Italy, the former bus failed the owners: due to engine failure, they were stuck in Switzerland. “It was a nightmare,” Tom recalls. - The police took our passports, and we had no right to leave the bus! I had to call a friend for help and change the engine.”

However, this story did not make the family disappointed in their mobile home. Children especially love him: after all, it was thanks to him that they visited French Disneyland!

The conversion of a regular bus into a travel van lasted for many years.

The car's floors are finished in wood and covered with carpets, so passengers feel right at home.

Tom had to make almost all the furniture for the van with his own hands.

According to Tom, the kitchen gave him the most problems.

Oddly enough, the family recently decided to put the fully finished and refurbished van up for auction on eBay. The starting price is 9,100 pounds, or about $12,000. “The children are terribly unhappy that we want to sell the van! - says Tom. “But we think it’s time to try something new and interesting.”

If you decide to make your own motorhome, you will need some basic knowledge, tools, a lot of patience and even more free time. And, of course, a reliable vehicle for creating a campervan.

This article contains some photographs of a mobile home built with your own hands on the basis of a Volkswagen car. Most of the tips can also be applied during the construction of motorhomes based on other cars.

Before you start, it is very important to read the next paragraph!

IMPORTANT! Before you start creating a camper with your own hands, it is necessary to legalize the implementation of such a procedure. In this case, you will be able to prevent various legal difficulties. Rules vary depending on the country, so we cannot publish uniform recommendations on this matter.

First steps

Building a mobile home with your own hands consists of the following steps:

Exterior works
Interior work
Water supply works
Gas and electricity
Furniture
Other

If the van will only be used by two people, there will be really plenty of space. If you are planning a trip for 3 or more people, you need to consider the number of seats. Remember that seats must be equipped with appropriate seat belts.

How many sleeping places will you need? One option is to arrange a bunk bed for children. If you have extra space under the roof, you can make a “drop-down” bed.

At this stage, you should have a clear plan for further action. Of course, you can improvise, but it's much easier to have a well-thought-out plan on paper.

Exterior works

The first thing you need to do when preparing a base vehicle is to thoroughly clean the inside of the car.

At this stage you also need to think about the shape of the body as a whole. It's time to deal with body damage and rust. Local or complete painting of the car will help.

Typically, vans do not have windows, so you may want to consider installing them. They are needed to ensure the flow of fresh air and sunlight into the motorhome. Windows come in different shapes and sizes, the choice depends on your preferences and body features.

During the construction of a motor home, you will have to make several holes in the body of the car. We are talking about openings for ventilation, gas outlet (in case of leakage), heater exhaust gases, water fillers, etc. Some of them may be done later, but it is much easier to solve the issue now if you know exactly where they will be.

Remember to apply primer in any areas where there is bare metal to prevent corrosion.

Build your own motorhome the right way!

Interior work

The van will most likely have a partition behind the front seats. Some partitions are attached with screws, others are welded to the body. A grinder will help solve the problem.

Remember to use protective equipment. Sparks can leave nasty stains on glass that are impossible to get rid of.

The fun begins. The insulation layer is very important as it will protect your camper from outside noise and temperature. There are many materials that can be used. The choice is up to you.

In this case it was used Armaflex material. It should be cut into pieces and glued. The main point is protection from moisture. If the insulating material does not protect against moisture ingress, it should not be used.

It is necessary to prepare insulating material, lightweight and moisture-proof plywood, as well as soft and flexible carpeting.

For the side covers, thicker plywood should be used, since furniture will be installed on them in the future.

Use a wide temperature range adhesive or sealant to secure insulation and carpeting to the sidewalls. Because the RV will be exposed to both freezing temperatures and the hot summer sun. The heating operation will also be affected. If you use low-quality glue, the work will have to be redone after some time.

Where to begin? Start sheathing your motorhome, from the roof to the flooring. First, we install the insulating and cladding layers on the ceiling, then we move on to the side panels.

Use wood strips on the floor to create enough space for insulation. The slats are secured to the floor using appropriate sealant. Then a layer of insulation is laid, after which it must be covered with plywood. The plywood is secured using sealant or screws.

Remember about the water supply, as well as the need to lay electrical cables and gas pipes. Wires and hoses can be routed through the insulation or under plywood covers if you already know where all the fixtures will be installed.

Water supply works

The RV must have a cold running water supply. To do this, place two cans of water under the sink. A submersible pump supplies water to the tap.

If you need warm water, an additional sink or shower, the system will be more complex. You can install large water tanks in other places, for example, under the van. You will need hoses to connect the entire system.

When you make a motorhome yourself, you are limited only by your imagination.

Don't forget about wastewater. You can install a suitable reservoir under the car or run a hose through the floor to drain the water into a portable tank or regular bucket.

Remember that used water smells terrible in summer and freezes in winter. Therefore, you need to get rid of it as soon as possible, so a bucket can be the ideal solution.

What about the toilet? You can install one of the convenient portable toilets.

Gas and electricity

IMPORTANT! Gas supply hoses and electrical wiring must only be installed by qualified personnel! If installed incorrectly, they can pose a serious hazard. Make your own motorhome, but don't put other people at risk.

Propane in the camper can be used for cooking, heating, and also connecting a refrigerator. You can do without it, using an electric stove and refrigerator, as well as an independent Webasto heater.

The gas cylinder must be stored in a separate place with holes in the bottom. Why does there have to be holes at the bottom? Because propane is heavier than air, it will always go down.

You could even make a valve to connect the gas stove to the outside of the car so you can cook outside the van in the future.

Again, build the camper properly for your own safety!

Electricity necessary to start all devices designed for 12V. The system consists of a battery, charger/converter, control panel and many wires.

Don't forget about the external connector for charging the motorhome battery from a regular electrical outlet (110V or 220V). You can also use it at home by charging the battery during winter storage.

In order to determine how much battery capacity you need, you will have to perform simple calculations. Let's say you will use the following:

Halogen lamps: 2×20W 2 hours a day = 80 Wh
Refrigerator: 45W 12 hours a day = 540 Wh

The total power consumption is 620 Wh per day. Now divide 620Wh by 12V and you get 52Ah. This is your daily power consumption. As a rule, a 100Ah battery will last about two days of battery life.

Make calculations taking into account the energy consumers you use. This will help you get the average daily electricity consumption figures.

Gas and electricity are very important issues to consider when building a campervan. If you plan to use the motorhome for traveling far from civilization, autonomy should be maximum. Take your time, think through everything carefully and calculate it.

Furniture

In this matter, nothing limits you either. You can confidently realize your dreams. There are many ways to make and install furniture.

Sometimes quite suitable furniture can be found at various disassembly sites, we advise you to search. Good offers sometimes appear at online auctions, and furniture is sometimes sold at a very affordable price.

You can also design everything from scratch. Some companies sell parts ready for installation, covered with veneer. All you have to do is apply varnish (if necessary) and install the furniture. You can also contact a professional to help you with this matter.

A motorhome on wheels, and even equipped with your own hands, is the dream of many lovers of auto travel and outdoor activities. It provides its owner with amazing freedom when traveling, freeing him from the need to find and book a hotel, purchase tickets, pack suitcases, etc. In addition, your own motorhome makes it easy to travel even with a large family, including pets - for this you need to use the appropriate furniture , as a rule, transforming.

When a motorhome-trailer on wheels first appeared on the road is quite difficult to answer. The first such experience was implemented by the Jennings company back in the 38th year of the last century, although home-made samples of motorhomes appeared much earlier. All motorhomes on wheels can be equipped with almost all the necessary attributes of a familiar and comfortable life - bathroom, shower, gas stove, full bed, which are present even in the smallest motorhomes, which in Russia are often based on a budget gazelle.

Depending on what type of motorhome it is, it can be:

trailed;
van;
combined.

A fairly common practice nowadays is the personal conversion of a suitable vehicle, such as a domestic gazelle, into comfortable motorhomes for travel. But before you make a motorhome on wheels with your own hands, you need to determine the main purpose of the conversion - long-term or short-term living in a motorhome, and also select or make the appropriate furniture.

Classes of mobile homes

According to the generally accepted classification, all motorhomes on wheels are divided into three main classes:

Attention! Any class “A” motorhome made on the basis of a bus or truck, according to the transport classification, requires the driver to have a category “C” license.

Speaking about the classification of motor home trailers, the following concepts should be highlighted:

Trailer tent

A homemade motorhome on wheels does not necessarily have to be expensive and difficult to manufacture, especially if it is used relatively rarely and for a small number of people. Some types of motorhomes do not even require the installation of furniture, and are used as a sleeping place. In order to make a motorhome-trailer yourself, you will need to put in some effort and a sufficient amount of time.

The main “power” element of such a motorhome, the frame, can be purchased ready-made, or you can assemble it yourself, which will require skill and certain technical knowledge. When making it yourself, special attention should be paid to anti-corrosion treatment of all steel elements of the future motorhome.

The frame, mounted on a chassis prepared for a motorhome, can be either steel or wood. When creating it, the main attention should be paid to the quality of the connection of parts, since when such a trailer-motorhome moves, the entire structure will be subject to serious dynamic and vibration loads. Inside such a motorhome you can place a fairly comfortable sleeping place, and when you stop for rest, the structure of the motorhome unfolds and a tent is quickly installed on top. Such a motorhome on wheels, the photo of which is presented below, is optimal for short trips and simple recreation in the fresh air.

Another version of such a trailer can be seen in the video:

How to make a motorhome on wheels with your own hands

In order to make a motorhome on wheels with your own hands, you can use any minibus, truck or even bus. In order to create it, you will need to put in a lot of effort, time, and be prepared for quite serious material investments, which will later more than pay off in comfort when traveling in your own motorhome.

The process of turning a standard gazelle into a motorhome on wheels will necessarily be accompanied by a number of works that are mandatory:

In the case where a trailer-motorhome is created for the purpose of long trips, It is advisable to provide a good audio-video system and satellite TV. If financial capabilities allow, then it would be a good option to install solar panels, which will extend the life of the generator.

Attention! In most cases, converting a vehicle into a motorhome trailer requires first legalizing all “alterations” in order to avoid legal problems in the future.

Interior work

Many people who like to travel comfortably are interested in the question of how much a motorhome on wheels costs in Russia, but after learning the cost of a ready-made option, they prefer to build a motorhome with their own hands. And this is not without meaning, since making a motorhome on wheels from a gazelle with your own hands is within the capabilities of any person who is ready to put in a certain amount of effort and spend their time on it.

The first thing that needs to be done inside the cabin of the future motorhome on wheels is to dismantle the partition located behind the passenger seats. If it is fastened with bolts, there will be no problems, but if a welded connection is used, you will need an angle grinder. After dismantling, the interior should be completely freed from interior decoration. At the same time, it is worth checking the metal parts for the presence of corrosion. Take measures to eliminate them, remembering that disassembling a finished motorhome will be much more difficult.

Before you begin insulation and interior decoration of the motorhome, you should carefully consider the water and electricity supply system, since it is better to hide all pipes and electrical cables under the casing - this will avoid accidental damage. After this, a motorhome on wheels based on a gazelle requires serious insulation. In addition to special materials with vibration-thermal insulation characteristics, basalt mineral wool or extruded polystyrene foam can be used for a motorhome.

An important point in finishing a motorhome on wheels inside and outside is the protective treatment of the material used. Thus, additional metal elements on the outside of the motorhome must have high-quality anti-corrosion treatment. Internal cladding elements are usually made of wood. To process them, it is recommended to use a special fire-bioprotective impregnation, which will prevent the spread of flames and will not allow the formation of fungus, which may simply be impossible to get rid of.

Certain ideas for creating your own project can be “borrowed” from the manufacturers of such houses by watching the following video:

Gas and electrical equipment

Any motorhome on wheels - a Mercedes or a gazelle - requires special treatment in terms of electricity and gas supply. You should not naively believe that, without having the appropriate education, you can perform high-quality electrical wiring and install the appropriate equipment in a motorhome. The same applies to gas equipment.

For example, few people know that for a gas cylinder in any motorhome it is necessary to “select” a separate closed area, in the lower part of which there must be holes communicating with the outside atmosphere. This allows propane, which is heavier than air, to “leave” the motorhome if it leaks from the cylinder, and not cause poisoning or a fire in the cabin.

An important point for a motorhome is the correct calculation of battery power. To ensure maximum autonomy, you should add up the daily energy consumption of all devices present in the motorhome. The resulting value in watts will need to be divided by 12 (V), resulting in a value in ampere hours (Ah) - this is what is indicated on the battery and allows you to judge its power. So, if the energy consumption in a motorhome is 50-60 Ah/day, it is optimal to purchase a battery of 120-150 Ah. Such a motorhome on wheels will be able to function autonomously for two days. It is advisable to provide an external outlet for recharging the motorhome battery in parking lots.

Furniture

Despite the fact that at present it will not be a problem to purchase ready-made furniture for a motorhome, according to reviews, it is not able to satisfy all the requests of car owners, especially those who create a motorhome on wheels according to their own drawings. Therefore, the best option is either to manufacture it yourself or to order it individually from a furniture manufacturer.

In most cases, it is more optimal for a motorhome to make your own furniture. Since for a small motorhome, for example, based on a standard gazelle or UAZ, not much furniture will be required, and it is not particularly complex, you can save money at this stage of the work. For the proper level of comfort in a motorhome, as a rule, the following furniture structures are made:

dining table; to save space in a small motorhome, it is better to use a folding version;
kitchen table with sink and work surface;
open shelves or drawers located under the ceiling of the motorhome;
If you have a toilet in a motorhome, you will need to make a partition with a door.

When a KamAZ or a bus is taken as a base for a motorhome, the amount of furniture listed above increases. When making a motorhome on wheels with your own hands, to facilitate the task of determining the type and quantity of furniture, you can use special computer programs, or draw a detailed plan for the future layout of the motorhome on paper, where you can clearly indicate not only the type of furniture, but also its location.

How the most expensive mobile home can be designed can be seen in the photo - it’s clearly visible how elegant and comfortable the interior decoration can be.

When building a mobile home with your own hands, you should pay attention to the quality of materials. Yes, for furniture It is advisable to use moisture-resistant materials that are resistant to household chemicals, since cleaning in any type of motorhome - a bus, trailer or gazelle - will have to be done quite often.

There are probably very few people who would not like to travel and at the same time spend the night at home, without using the services of hotels or hotels. Many will say that this is impossible and any trip is accompanied by a hotel room. However, there is a solution - a motorhome or motorhome. You've probably seen such mobile structures in foreign films. And this is not strange, because let’s say in America, according to statistics, every 3 residents have a mobile home.

Such a house is not only convenient and comfortable, but also significantly saves money, since the question of finding housing disappears. You can talk about the advantages of a motorhome for a long time, and there really are many of them. However, there is one drawback - a caravan is not a cheap pleasure. But if you have patience and hard work, there is a way out - to build a mobile home on wheels with your own hands.

The main need for such a house is travel, which you can easily go on with your family and even small children. A motorhome is also useful for business trips; you don’t have to look for hotels, book rooms, collect luggage and carry it with you.

The main thing is that the driver is experienced, with good driving experience and, of course, with a positive attitude towards this type of transport.

Motorhome: what you need for comfort

Although the house will be in the form of a mobile home, this does not mean that it should not be comfortable and satisfy the minimum needs of the owners.

Home lighting

To supply light to a mobile home you will need:

rechargeable battery;
charger;
wire system for subsequent electrical wiring;
panel for controlling the supply of electricity.

Heating for home

To heat your home, you can use several types of heaters, this can be an autonomous type or a gas cylinder. It is preferable to use gas, since in addition to heat it will provide the possibility of cooking.

If you choose heating using gas, then you will have to seek help from a specialist. Of course, building everything with your own hands from start to finish is commendable, but you should remember the safety of passengers.

Air (ventilation) for home

Ventilation is very important, especially when using gas. In this case, there should be several holes, and one of them will be as low as possible.

For comfort: water, bathroom, kitchen

No housing will be comfortable if it lacks basic amenities. Think carefully about where exactly the kitchen, mini portable dry closet and shower will be located. Also don’t forget about water tanks and water pumps.

It is better to send the water that will be drained into a large bucket located under the body. To do this, you can use a special hose that should be laid in the floor.

Motorhome furniture

Certain difficulties may arise with furniture, since it should be as compact as possible. For such housing, folding furniture is used, it is mounted on the walls. In most cases, it is possible to purchase such furniture only on order, which is quite expensive. But if you have the opportunity to do it yourself, it will save a lot of money.